We cut to size your Gate - You assemble and Install

DIY

- SMS me your size to 0414237573

- Tell me what height and width

- Tell me colour of slats  - Black, white, light grey, dark grey, teak, red cedar or merbau

- Tell me if you want black, white, Dark Grey or Merbau gate frames

- Tell me if you want 10mm or 16mm or 40mm gaps between the slats

For example a typical 1800mm tall and 1000mm wide gate and supplied in DIY form (which still needs assembly by you) would cost around $379 or $210 per SQM.

If you want us to assemble then supply and build is $90 extra (1000m or under).  We do not install at your location and the pickup is from Narangba. (e.g. price above is for 16mm gaps and black slats)

We make CUSTOM TO YOUR SIZES 

We can supply to suit either horizontal slats or vertical slats.  Please specify or it will be made to suit traditional horizontal.

NOTE: We use a reinforced T-Channel for the gates top and bottom rail when doing Horizontal gates.  So the gates won't generally line up with a slat fence when next to each other, unless you advise us they need to.  When we see you asking for a gate and fence combo normally we'll supply different profiles than what is on this page.  If is critical to you to line up and with varying heights then you may want to change the gate to a vertical slats to make it opposite.

What you should know:

- Payment of $100 needs to be made for any custom orders of small gates

- We cut Tuesdays and Thursday each week so have orders in before that

- Protective sheets will be left on the material for you to remove.

- Allow 2-5mm difference in final size as all is hand cut

- When we quote you slat gaps (10mm or 16mm or 40mm) this will be the gap between the slats.  The gap between the first slat and last slate to the frame will be equal.  This is because we do not cut (or rip) slats long ways.  So if you want the same gap all the way through your gate then ask us for a height close to your needs that divides equal.

- If you buy DIY the tools you would need to build the gate would be a Tek drill, tape measure and a Square.

 

Gate outside frame material is available in:

- Satin Black frame

- Gloss White frame

- Dark grey

- Merbau

When cut allow a -5 to +5 tolerance for the size you ask.  Also you should be leaving clearances to fit your own hinges and locks.  Select a hinge that allows you to adjust the gates gaps.  Depending on the height of the gate you should be able to adjust the gates square by 5 to 10mm easily.  Some hinges need gaps of 10mm to 30mm and some locks sit on the inside of frame and have magnet catches so the clearance could be between 10mm to 15mm.

We sell a hinge that sits inside the 50x50 channel on the side of the gate. 

Further Information on Installation

* You need to have DIY experience

* Price does not come with any posts

* Heavy Duty alloy 76mm x 76mm posts are available from our warehouse at $40lm

* Instructions are provided 

* Each install and each home is different.  You may need extra hardware or less hardware.

*At least 2 people needed to install

 

These tough surface finishes are guaranteed for ten years – Our aluminium gates require virtually no maintenance.

A periodic wipe down keeps them looking as good as new – Aluminium gates don’t rot, warp, crack, dry out or soak up water.

 The physical changes that stop wooden gates opening and closing properly don’t affect aluminium – Aluminium gates are perfect for automation.

They are strong yet light and do not expand and contract like wood – And now you can have your own, low maintenance, long lasting, beautiful aluminium gates without breaking the bank. 

Lightweight and robust - Our high quality aluminium gates offer a no maintenance alternative to traditional wood and steel counterparts, aluminium will not be affected by the changing weather conditions

Powder Coated Finish - Offers extra protection that will keep the gates looking like new for years to come.

 

So you will have NO RUST and the surface stays is POWDER COATED to last a decade

  

Note

We supply gates only.  We do not do measure and quotes or installs. If we assemble the Gates it could be up to 10mm out of square adjustment or size adjustment but can be adjusted and squared using our hinges.

Example prices in the below table (Does not include hinges or latches)

- Frame Material (Black, White, Dark Grey or Merbau)

- Slat Inserts (Black, White, Greys if you want woodgrain Browns add around 15%)

- Screws and Spacers included

- Horizontal slats

- 16mm gaps but we can also do 10mm or 40mm gaps with price adjustment

Gate Heights to allow even spacing between slats and also the gate frame

TO HAVE EXACTLY SAME GAPS BETWEEN THE SLATS AND ALSO THE FRAME  USE THESE HEIGHTS BELOW, FOR HORIZONTAL SLATS. IF YOU DON'T THEN ALL WE DO IS MAKE THE GAP BETWEEN TOP AND BOTTOM FRAME TO FIRST SLATE EVEN

ANY HEIGHT CAN BE MADE - WE CUSTOM MAKE ALL OUR SLAT GATES AND PROVIDE EITHER FULL MADE OR DIY

Delivery and Pickup

FREE pickup from Narangba Warehouse. Usually need 2 hours’ notice to pick order

$140 Northside Brisbane delivery

$200 Southside Brisbane Delivery

$250 Sunshine or Gold Coast Delivery

$350 Flat Rate Sydney

$450 Flat Rate Melbourne