Double Swing Gates - CUSTOM Width and Height  - 8 Colour Slats - Price per SQM roughly

We cut to size your Gate - You assemble and Install

DIY so MESSAGE us this info below to get a Factory Direct Price

- Tell me what height and width

- Tell me colour of slats  - Black, white, light grey, dark grey, cream, red cedar or merbau

- Tell me if you want Black, White, Cream, Dark Grey or Merbau gate frames

- Tell me if you want 0mm or 10mm or 16mm or 40mm gaps between the slats

For example a typical 1800mm tall and 1500mm wide gate and supplied in DIY form (which still needs assembly by you) would cost around $665 or $255 per SQM. So with 2 swinging next to each other would be as an example 3000mm wide and around $1330.

If you want us to assemble then supply and build is $150 extra per large gate  We do not install at your location and the pickup is from Narangba. (e.g. price above is for 16mm gaps and black slats)

We only make CUSTOM TO YOUR SIZES and jobs ready in 2 working days

We can supply to suit either horizontal slats or vertical slats.  Please specify or it will be made to suit traditional horizontal.


NOTE: We use a reinforced T-Channel for the gates top and bottom rail when doing Horizontal gates.  So the gates won't generally line up with a slat fence when next to each other, unless you advise us they need to.  If is critical to you to line up and with varying heights then you may want to change the gate to a vertical slats to make it opposite.

What you should know:

- Payment of $100 per gate needs to be made for any custom orders 

- We cut Tuesdays and Thursday each week so have orders in before that

- Protective sheets will be left on the material for you to remove.

- Allow 2-5mm difference in final size as all is hand cut

- When we quote you slat gaps (0mm or 10mm or 16mm or 40mm) this will be the gap between the slats.  The gap between the first slat and last slat to the frame will be equal.  This is because we do not cut (or rip) slats long ways.  So if you want the same gap all the way through your gate then ask us for a height close to your needs that divides equal.

- If you buy DIY the tools you would need to build the gate would be a Tek drill, tape measure and a Square.

Gate outside frame material is available in:

- Satin Black frame
- Gloss White frame
- Dark grey
- Merbau
- Cream


When cut allow a -5 to 5 tolerance for the size you ask.  Also you should be leaving clearances to fit your own hinges and locks.  Select a hinge that allows you to adjust the gates gaps.  Depending on the height of the gate you should be able to adjust the gates square by 5 to 10mm easily.  Some hinges need gaps of 10mm to 30mm and some locks sit on the inside of frame and have magnet catches so the clearance could be between 10mm to 15mm.


We sell a hinge that sits inside the 50x50 channel on the side of the gate. 


Further Information on Installation

* You need to have DIY experience

* Price does not come with any posts

* Heavy Duty alloy 76mm x 76mm posts are available from our warehouse at $40lm

* Instructions are provided 

* Each install and each home is different.  You may need extra hardware or less hardware.

*At least 2 people needed to install


These tough surface finishes are guaranteed for ten years – Our aluminium gates require virtually no maintenance.

A periodic wipe down keeps them looking as good as new – Aluminium gates don’t rot, warp, crack, dry out or soak up water.
 

- Aluminium gates are perfect for automation.

They are strong yet light and do not expand and contract like wood – And now you can have your own, low maintenance, long lasting, beautiful aluminium gates without breaking the bank. 

Lightweight and robust

Powder Coated Finish - Offers extra protection that will keep the gates looking like new for years to come.


So you will have NO RUST and the surface stays is POWDER COATED to last a decade

 
Note

We supply gates only.  We do not do measure and quotes or installs. If we assemble the Gates it could be up to 10mm out of square adjustment or size adjustment but can be adjusted and squared using our hinges.

Pickup
Can be arranged from Narangba 5.5 days a week. We are a real seller and our warehouse in the North of Brisbane near North Lakes.

BULKY GOODS DELIVERY

- If only buying 1 x gate or 1 x panel then Australia wide wrapping and shipping is =$120.  

- If buying more, then see the flat rate shipping Info below:

-$140 flat rate fee to the Northside of Brisbane

-$200 flat rate fee to the Southside of Brisbane

-$250 flat rate fee to the Gold Coast, Ipswich or Sunshine Coast

-$350 flat rate fee to Sydney or Rockhampton

-$450 flat rate fee to Melbourne or Townsville

**We use backload trucks for most of the above and usually do all drops in other country towns we pass but following that main highway.  Sometimes these deliveries will be after hours

-All other areas we can quote to a home in your state or country town